FDJ-120风动手持切割锯是我公司针对高危，安全系数要求特别高的工作环境，如化工.治炼厂.天然气开采.高危潮湿的隧道，水下及狭窄的空间作业，尤其是高瓦斯防爆矿井。山西万泽锦达矿山机械设备有限公司自主研发的新型多用途风动手持切割工具。它使用台湾进口气动马达作为动力输出，利用压缩空气作为动力源，不用电源。风动手持切割锯不但整机重量轻，操作简单，携带方便零火花，提高工作效益。本产品安全可靠是高危行业的最理想气动切割工具。
一．技术参数:1适用材料:不锈钢.铝，铜.铬合金，镍基合金，玻璃，纤维，木材，塑料，钢丝绳等。2切割范围：120mm*120mm圆型材料，220mm*120mm方型材料。3工作压力：0.3—0.8Mpa4外型尺寸：650*210*270
二．矿用轨道轻型3分钟轨道重型5分钟三.优点1.90°直切,45°斜切,立式切割一体机。2.运转速度只有砂轮机的1/60,安全无火花。3.切缝窄0.5mm,切割表面平整，精度高，无挂渣，无脱碳。4.锯条使用寿命长，单位切割成本低，一根锯条使用寿命等同于50-80片砂轮切割片，较电能锯节能60%

使用方法：
1、了解所需切割的材料，如有必要可以通过降低空气压力来降低锯片的转动速度。
2、确保牢固固定了所需切割的材料，防止其移动。
3、气动空气马达时，用手指按压阀杆，然后开始切割。
4、用锯的重量来控制切割压力。对于较软的材料来说，这样的重量已经足够。过多的压力会降低锯片的速度。对于较硬的材料，可以通过加压的方式来降低锯片的转动速度。切割是保持锯笔直。锯片的任何扭曲或歪斜都可能降低其使用寿命。（注意：避开切割后可能掉落的碎片。切割即将完成时，切勿使锯碰到您的身体、工件或附近的其它人员。）
5、关闭空气马达时，释放阀杆。
6、下次切割开始前，锯片必须保持运动状态。气动锯时，锯片不能接触任何表面。
7、断开空气软管时，关闭空气软管阀。断开前，先打开空气阀给软管减压。
8、更换锯片前，务必断开空气软管，并推动阀杆以释放掉马达内的压力。
9、顺时针转动调整手柄以便释放锯片导杆上的张力。然后释放侧面板的锁以便打开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开

Commodity introduction:
The FDJ-120 type pneumatic cutting saw is suitable for the risk working environment. It can operate in a high temperature environment, no sparks, and no leakage risk in humid environment. It is a reliable, safe and highly efficient aspiration pneumatic thing. It is widely used in mining, petrochemical, construction and other professions.
Use the downhole air pressure pipe system as a power source. The weight is light and easy to be carried; it is scientific and easy to work. Si Li Zhen
The pipeline, cable, angle steel, structural steel, U type steel, chain, bolt, anchor cable and so on can be cut off quickly.
Super - Han bl steel alloy saw blade, high temperature resistance, long life, the use of conflict. It is very suitable for sawing stainless steel, nickel base alloy, iron, copper, aluminum, glass, plastic, wood and so on.

Technical beters:
Type power consumption cutting b (diameter) blade speed weight
FDJ-120 1kW 0.6 120mm 60m/min 6kg
Pneumatic pneumatic cut saw application b:
1. Knowing the material that needs to be cut, it is necessary to reduce the speed of the saw blade by reducing the pressure of the air.
2, ensure that the material needed to be cut is fixed to prevent its movement.
3. When pneumatic air motor, press the stem with the finger, and then cut it initially.
4, the cutting pressure is controlled by the weight of the saw. This weight is now satisfactory for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of the saw blade can be reduced by pressure. The incision is to keep the saws straight. Saw any distortion or skew can reduce the use of life. (notice: avoid debris that can fall after a cut. When the cut is about to end, do not make the saw touch your body, the workpiece, or the other people in the neighborhood.
5. When the air motor is closed, the stem is released.
6. Before the next incision, it is necessary to adhere to the movement of the saw blade. The saw blade can't contact any surface when a pneumatic saw. Yanshi city FDJ-120/ mine explosion-proof cutting saw
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, it is necessary to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.

A few points need to be paid attention to for safe operation.
1. the weight of the saw is used to control the pressure of the cutting. This weight is enough for softer materials. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life
2. release the stem when the motor is turned off.
3. before replacing the blade, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
4. clockwise rotation of the handle to release the blade and release it from the guide rod.
5. the saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
6. understand the required cutting material and reduce the speed of the saw blade by reducing the air pressure if necessary.
7. ensure that the required cutting material is firmly fixed to prevent its movement.
8. pneumatic motor, press the stem with the finger, then start cutting.
9. when the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.