产品介绍
  FDJ-120手持切割锯是我公司针对高危，安全系数要求特别的工作环境，如化工.治炼厂.天然气开采.潮湿的隧道，水下及狭窄的空间作业。山西万泽锦达机械制造有限公司自主研发的新型多用途气动手持切割工具。它使用德国进口锯条，利用压缩空气作为动力源。气动手持切割锯不但整机重量轻，操作简单，携带方便无火花，提高工作效益。本产品安全可靠是切割行业的最理想气动切割工具。

适用范围
    ·该锯适用于安全的工作环境，可在较高温的环境下作业，无火花，是一款性能可靠、安全型及效率极高的理想气动工具之一。广泛用于电缆、方管、建筑等行业。
   ·利用两相电系统作为动力源。重量轻，易携带；结构科学，便于作业。
   ·可快速切割管道、电缆、角钢、结构钢、U型钢、链条、锚杆、锚索等。
   ·锢金属钢合金超级锯条，耐高温、耐摩擦、使用寿命长。非常适用于锯割不锈钢、镍基合金、铁、铜、铝、玻璃、塑料、木材等。

 

技术参数：

型号  FDJ-120 

功率  1.5kw 

耗气量  0.6 

切割宽度（直径）  120mm 

锯片速度  60m/min

重量  6kg 

使用方法：

1、了解所需切割的材料，如有必要可以通过降低空气压力来降低锯片的转动速度。 

2、确保牢固固定了所需切割的材料，防止其移动。 

3、气动空气马达时，用手指按压阀杆，然后开始切割。 

4、用锯的重量来控制切割压力。对于较软的材料来说，这样的重量已经足够。过多的压力会降低锯片的速度。对于较硬的材料，可以通过加压的方式来降低锯片的转动速度。切割是保持锯笔直。锯片的任何扭曲或歪斜都可能降低其使用寿命。

（注意：避开切割后可能掉落的碎片。切割即将完成时，切勿使锯碰到您的身体、工件或附近的其它人员。） 

5、关闭空气马达时，释放阀杆。 

6、下次切割开始前，锯片必须保持运动状态。气动锯时，锯片不能接触任何表面。 

7、断开空气软管时，关闭空气软管阀。断开前，先打开空气阀给软管减压。 

8、更换锯片前，务必断开空气软管，并推动阀杆以释放掉马达内的压力。 

9、顺时针转动调整手柄以便释放锯片导杆上的张力。然后释放侧面板的锁以便打开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开。 

Technical beters:
Type FDJ-120
Power 1.5kw
The gas consumption 0.6
The cutting b (diameter) 120mm
Blade speed 60m/min
The weight of 6kg


Using b:
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.  
2, ensure that the required cutting material is firmly fixed to prevent its movement.  
3. When pneumatic air motor is operated, the stem is pressed with the finger, and then the cutting is started.  
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life.
(notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity.  
5. When the air motor is closed, the stem is released.  
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.  
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.  
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.  
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod