北格镇梁家庄FDJ-230气动切割锯小锯床招商信息-机电一体化网

产品简介

北格镇梁家庄FDJ-230气动切割锯小锯床

产品价格：￥4600

上架日期：2018-01-03 16:46:10

产地：山西省太原市小店区北格镇东浦村孝信工业园区

发货地：山西省太原市小店区北格镇东浦村孝信工业园区

供应数量：不限

最少起订：1台

浏览量：307

点击询价 QQ洽谈

资料下载：暂无资料下载

其他下载：暂无相关下载

详细说明

化液无火花切割锯江苏宿迁说明”更多信息

产品（FDJ-120型风动切割锯）介绍：

FDJ-120型乳化液切割锯，适用于较危险的工作环境，可在较高温的环境下作业，无火花，在潮湿的环境中无漏电危险，是一款性能可靠、安全型及效率极高的理想风动工具之一。广泛用于采矿、石化、建筑等行业。

利用井下乳化液系统作为动力源。重量轻，易携带；结构科学，便于作业。

可快速切割管道、电缆、角钢、结构钢、U型钢、工字钢、轨道、链条、锚杆、锚索等。

锢金属钢合金超级锯条，耐高温、耐摩擦、使用寿命长。非常适用于锯割不锈钢、镍基合金、铁、铜、铝、玻璃、塑料、木材等。

优点：安全防爆、轻巧便携、锯割范围广泛。

手持式气动/乳化液切割锯常规技术参数：

型号	功率	耗气量(m3/min)	切割厚度	切割宽度（直径）	锯片速度	重量
120	0.5kw	0.6	三种锯片： 0—30mm 30—50mm 50—120mm	120mm	60m/min	6kg
180	1.0kw	1.2		180mm	90m/min	10kg
230	1.5kw	1.5		230mm	120m/min	16kg

使用方法：
  1、了解所需切割的材料。
  2、确保牢固固定了所需切割的材料，防止其移动。
  3、电源接上时，用手指按压阀杆，然后开始切割。
  4、用锯的重量来控制切割压力。对于较软的材料来说，这样的重量已经足够。过多的压力会降低锯片的速度。对于较硬的材料，可以通过加压的方式来降低锯片的转动速度。切割是保持锯笔直。锯片的任何扭曲或歪斜都可能降低其使用寿命。（注意：避开切割后可能掉落的碎片。切割即将完成时，切勿使锯碰到您的身体、工件或附近的其它人员。）
  5、下次切割开始前，锯片必须保持运动状态。电动锯时，锯片不能接触任何表面。
  6、更换锯片前，务必断开电源力。
  7、顺时针转动调整手柄以便释放锯片导杆上的张力。然后释放侧面板的锁以便打开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开。
为了安全作业需要注意以下几点：
   1、用锯的重量来控制切割压力。对于较软的材料来说，这样的重量已经足够。过多的压力会降低锯片的速度。对于较硬的材料，可以通过加压的方式来降低锯片的转动速度。切割是保持锯笔直。锯片的任何扭曲或歪斜都可能降低其使用寿命
  2、关闭电源时，释放阀杆。
  3、更换锯片前，务必断开电源。
  4、顺时针转动调整手柄以便释放锯片导杆上的张力。然后释放侧面板的锁以便打开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开。
  5、下次切割开始前，锯片必须保持运动状态。电动锯时，锯片不能接触任何表面。
  6、了解所需切割的材料。
  7、确保牢固固定了所需切割的材料，防止其移动。
  8、接电源时，用手指按压阀杆，然后开始切割。
  9、断开电源时，关闭电源软管阀。断开前，先打开电源阀给软管减压

联系人金经理电话13934240041

More about the mining wind cutting saw:
Bolt cutting saw is in mine roadway, the roadway repair, used to trim the length of anchor a supporting tool, it can be safely and quickly cut off the high strength bolt diameter below 24 mm; in addition, it also solves the problem of air inlet area, goaf, goaf, air return area, fast falling roof caving the issue of angle, make the gas and coal dust accumulation amount reduced, preventing the accumulation of gas and coal dust hazard.
Cutting materials and applicable scope: (hand held explosion-proof cutting saw is mainly used for cutting coal mines, high gassy mines, oil pipelines, natural gas pipelines, cables and so on, which requires no sparks in the cutting process).
Iron, steel, copper, iron, copper, cable, anchor, steel mesh, I-beam, channel steel, U steel, H steel, steel, steel, steel, coal miners C steel rail.
FDJ-120 type mine emulsion pipe cutting saw, cable emulsion non spark cutting saw, the emulsion of -120 type coal mine angle cutting saw, mine explosion-proof structure steel cutting saw, FDJ-120 type tunnel U type steel cutting saw, I-beam without spark cutting machine, FDJ-120 type track cutting cutting saw, chain saw, cutting off the coal mine FDJ-120 type mine anchor cable cutting saw, pneumatic hand-held cutting saw no spark...
FDJ-120/180/230 hand-held emulsion / wind cutting saw use b:
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
2, ensure that the required cutting material is firmly fixed to prevent its movement.
3. When the emulsion motor is motor, the stem is pressed with the finger and then the cutting is started.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity.
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
Shanxi million Zejin Machinery Equipment Manufacturing Co., in 2002 began to engage in the specific work of mining engineering, then according to their own demand, starting their own R & D and production of series of mining machinery needs, and transbation into today, customers all over the country, machinery manufacturing industry leader. It is a factory specializing in mining equipment, the company produces the mine / emulsion pneumatic cutting saw technology mature, the quality is excellent.