FDJ-230多功能切割锯黄石用途FDJ型轻轨切割锯宜昌哪家好？？FDJ-230高强度切割锯图木舒克原料FDJ-230多功能切割锯黄石用途高品质气动风动切割锯桂林质量杠杠的FDJ-120油气管道切割锯甘南怎么样井下防爆风动气动切割锯苏州哪里便宜

FDJ-120风动手持切开锯是我公司关于高危，安全系数请求特别高的作业环境，如化工.治炼厂.天然气挖掘.高危潮湿的地道，水下及狭窄的空间作业，尤其是高瓦斯防爆矿井。山西万泽锦达矿山机械设备有限公司自立研制的新式多用途风动手持切开东西。它使用台湾进口气动马达作为动力输出，使用压缩空气作为动力源，不必电源。风动手持切开锯不光整机分量轻，操作简略，携带方便零火花，进步作业效益。本商品安全可靠是高危职业的抱负气动切开东西。

联系人金经理电话13934240041

FDJ-120风动切割锯技术参数:

1：适用资料:不锈钢.铝，铜.铬合金，镍基合金，玻璃，纤维，木材，塑料，钢丝绳等。

2：切开规模：120mm*120mm圆型资料，220mm*120mm方型资料。

3：作业压力：0.3—0.8Mpa

4：外型尺度：650*210*270

FDJ-120风动切割锯长处

1：90°直切,45°斜切,立式切开一体机。

2：运转速度只要砂轮机的1/60,安全无火花。

3：切缝窄0.5mm,切开外表平整，精度高，无挂渣，无脱碳。

4：锯条使用寿命长，单位切开成本低，一根锯条使用寿命等同于50-80片砂轮切开片，较电能锯节能60%

FDJ-120风动切割锯使用方法：

1、了解所需切开的资料，如有必要能够经过下降空气压力来下降锯片的滚动速度。矿用锚杆锚索切割锯宁夏 优质

2、保证结实固定了所需切开的资料，避免其移动。

3、气动空气马达时，用手指按压阀杆，然后开端切开。

4、用锯的分量来操控切开压力。关于较软的资料来说，这么的分量已经满足。过多的压力会下降锯片的速度。关于较硬的资料，能够经过加压的方法来下降锯片的滚动速度。切开是坚持锯垂直。锯片的任何歪曲或倾斜都也许下降其使用寿命。（留意：避开切开后也许坠落的碎片。切开行将完结时，切勿使锯碰到您的身体、工件或邻近的其它人员。）

5、封闭空气马达时，开释阀杆。

6、下次切开开端前，锯片有必要坚持运动状况。气动锯时，锯片不能触摸任何外表。

7、断开空气软管时，封闭空气软管阀。断开前，先翻开空气阀给软管减压。

8、替换锯片前，有必要断开空气软管，并推进阀杆以开释掉马达内的压力。

9、顺时针滚动调整手柄以便开释锯片导杆上的张力。然后开释侧面板的锁以便翻开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开。

Cutting materials and applicable scope: (hand held explosion-proof cutting saw is mainly used for cutting coal mines, high gassy mines, oil pipelines, natural gas pipelines, cables and so on, which requires no sparks in the cutting process).
Iron, steel, copper, iron, copper, cable, anchor, steel mesh, I-beam, channel steel, U steel, H steel, steel, steel, steel, coal miners C steel rail.
FDJ-120 type mine emulsion pipe cutting saw, cable emulsion non spark cutting saw, the emulsion of -120 type coal mine angle cutting saw, mine explosion-proof structure steel cutting saw, FDJ-120 type tunnel U type steel cutting saw, I-beam without spark cutting machine, FDJ-120 type track cutting cutting saw, chain saw, cutting off the coal mine FDJ-120 type mine anchor cable cutting saw, pneumatic hand-held cutting saw no spark...
FDJ-120/180/230 hand-held emulsion / wind cutting saw use b:
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
2, ensure that the required cutting material is firmly fixed to prevent its movement.
3. When the emulsion motor is motor, the stem is pressed with the finger and then the cutting is started.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity.
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
Shanxi million Zejin Machinery Equipment Manufacturing Co., in 2002 began to engage in the specific work of mining engineering, then according to their own demand, starting their own R & D and production of series of mining machinery needs, and transbation into today, customers all over the country, machinery manufacturing industry leader. It is a factory specializing in mining equipment, the company produces the mine / emulsion pneumatic cutting saw technology mature, the quality is excellent.