产品介绍：

·该锯适用于危险的工作环境，可在较高温的环境下作业，无火花，在潮湿的环境中无漏电危险，是一款性能可靠、安全型及效率极高的理想风动工具之一。广泛用于采矿、石化、建筑等行业。

·利用井下压风管道系统作为动力源。重量轻，易携带；结构科学，便于作业。

·可快速切割管道、电缆、角钢、结构钢、U型钢、链条、锚杆、锚索等。

·锢金属钢合金超级锯条，耐高温、耐摩擦、使用寿命长。非常适用于锯割不锈钢、镍基合金、铁、铜、铝、玻璃、塑料、木材等。技术参数：

辽宁抚顺市矿用U型钢切割锯手持式FDJ-230型大行程气动无火花切割锯厂家

联系人金经理电话13934240041

微信号13934240041

型号	功率	耗气量		切割宽度（直径）	锯片速度	重量
WZJ-120	0.5kw	0.6		120mm	60m/min	6kg

1、了解所需切割的材料，如有必要可以通过降低空气压力来降低锯片的转动速度。

2、确保牢固固定了所需切割的材料，防止其移动。

3、气动空气马达时，用手指按压阀杆，然后开始切割。

4、用锯的重量来控制切割压力。对于较软的材料来说，这样的重量已经足够。过多的压力会降低锯片的速度。对于较硬的材料，可以通过加压的方式来降低锯片的转动速度。切割是保持锯笔直。锯片的任何扭曲或歪斜都可能降低其使用寿命。（注意：避开切割后可能掉落的碎片。切割即将完成时，切勿使锯碰到您的身体、工件或附近的其它人员。）

5、关闭空气马达时，释放阀杆。

6、下次切割开始前，锯片必须保持运动状态。气动锯时，锯片不能接触任何表面。

7、断开空气软管时，关闭空气软管阀。断开前，先打开空气阀给软管减压。

8、更换锯片前，务必断开空气软管，并推动阀杆以释放掉马达内的压力。

9、顺时针转动调整手柄以便释放锯片导杆上的张力。然后释放侧面板的锁以便打开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开。

辽宁抚顺市矿用U型钢切割锯手持式FDJ-230型大行程气动无火花切割锯厂家

联系人金经理电话13934240041

微信号13934240041

FDJ-120 pneumatic cutting saw use b:
1. Understand the material that needs to be cut, such as the reduction of air pressure to reduce the rolling speed of the saw blade. Cutting and sawing Ningxia high quality with mining bolt and anchor cable
2, ensure the sturdy fixation of the required open data to avoid its movement.
3. When pneumatic air motor, press the stem with the finger, and begin to cut.
4, use the component of the saw to control the cut pressure. For the softer data, this component has been satisfied. Too much pressure will reduce the speed of the saw blade. With more hard data, the rolling speed of the saw blade can be reduced by a pressurized b. The incision is to stick to the saw vertical. Any distortion or tilt of the saw may decrease its service life. (notice: avoid fragments that may fall after a cut. Do not make the saw touch your body, the workpiece, or the other people in the neighborhood when the cut will be finished.
5. When the air motor is closed, the stem is released.
6. Before the next opening, it is necessary to adhere to the movement of the saw blade. When a pneumatic saw, a saw can't touch any appearance.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, it is necessary to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.